00:05Hello and welcome to another video today I've been unboxing this, it's a playstation 2, it's a Japanese slim model
00:10playstation 2
00:12So let's open it, there's no games with accessories or controllers or power cord or anything, it's just the system
00:17itself
00:18This is going to be a bit of scissors
00:41The next thing I'm probably going to have to do down here to get rid of the tape
01:07And here it is, there's a push here, make sure that it's labeled to remind you how to close it
01:18And so you've got the button to open it up, put your laser back there
01:24Part that's been in the disc, there's the power button, it says playstation 2 up here
01:30We've got sony, we've got some vents, we've got IR port and infrared
01:36We've got two USB ports, two memory cards and two controller ports
01:43Here's the side, the back
01:47Here we have AV out, optical out, network
01:53A place to plug an ethernet cable in
01:56We've got a power jack here, 8.5 volts in
02:00And on the bottom, just the beaten up barcode
02:08So as you can see I've got the video plug in here
02:12And I've just got the power cable here
02:17So this is an Australian power brick
02:19So in theory they should both work together
02:21So let's plug it in and let's have a go
02:33Ok let's press power
02:40So I'm going to be disassembling the slim PS2 just because
02:44That doesn't work at the moment
02:46Then you can figure out what's wrong with it
02:56So I'm going to go next
02:57You can check it out
03:03Now let's go back to the previous line
03:03So here's the general blade
03:04You can check it out
03:18I'm going to be able to work there
03:27There's six feet, need to take off, these two are just under rubber and the other one
03:32need to take off.
03:33These ones have four plastic bits and they're much harder to remove, there's one, these
03:45feet don't have anything under them.
04:15Okay, so we're going to take these four out.
04:49And the last one, it looks like it will be hard to take off with everything with this sticker.
05:06I'm going to try to lift it from this side to the front, just have the stick on the back
05:11and it's sort of a hinge.
05:16I'm just going this side off, I'm going to try to move around, also it might actually hinge
05:27at this far, so I'm going to have to remove the stick at the back and rotate the whole
05:34thing this way, like that.
05:40So I've just got the back corner off, so I hope I can peel it.
05:48And I hope that's stripped.
05:51So I'm going to have to just move it off camera.
05:54So it looks like what teared was originally just the top layer of film.
05:59I was able to get the bottom layer just up, and up just using a pair of pliers.
06:04As you can see it now says ROID all over it.
06:25Now I can't imagine the form to use Slippy Palad to begin with.
06:36Okay.
06:41I think the reason it only came up one way is because of that this section here is sort
06:45of acting as a hinge.
06:49Oh, there it's got little pins sticking in.
06:53I think some of it broke because it looks like there's a part there, but over here there's
07:00a part missing.
07:01So I think that broke and I took it off.
07:10I'll just plug it in and see what happens.
07:17So it does seem quite warm.
07:22I don't know if it was being exposed to water or something, but the metal layer doesn't
07:27seem in that good condition.
07:34Something's happening as I touch it.
07:39Now we need a heatsink, and then disk drive over this side, and we'll look at the battery.
07:52So that switch is detected for the disk drives down.
07:56So I'm going to continue with the teardown, taking the battery out, and I'll just lift it
08:00up with the IR sensor.
08:03So I'm going to take the battery out.
08:05and 2 point out.
08:35So before we get into that圖.
09:03Ok, we're taking out the disk drive now.
09:11These are the new screws, they also have a full of absorbers to stop fibrations.
09:42Here we go.
09:50Here we go.
09:58Here we go.
10:00Here we go.
10:09Here we go.
10:19Here we go.
10:37Here we go.
10:42Here we go.
10:43Here we go.
10:44Here we go.
10:44Here we go.
10:55Looks like it wasn't actually necessary to take most of those out just to get this out.
10:59Here we go.
11:04Here we go.
11:05Here we go.
11:09Here we go.
12:48It looks like maybe we did have to take the screws out from the other end.
12:52I think there's one there.
13:00I'm not sure what this is.
13:01The little light gets on the solder here.
13:04I'm actually perfectly normal.
13:07Kind of not see if I'm into the solder.
13:37I'm not sure what this is.
13:38I'm not sure what this is.
14:08I'm not sure what this is.
14:08I'm not sure what this is.
14:37I'm not sure what this is.
15:08I'm not sure what this is.
15:08I'm not sure what this is.
15:08I'm not sure what this is.
15:11Here we go.
