00:00Assalam-o-Alaikum, In this kit, there was an error of F1 which was not getting removed.
00:07And this brother has sent it to us, he is a mechanic, he had sent it.
00:11He checked everything, but the error of F1.
00:13Now, it has been checked.
00:15In its low side, the IPM, you will get my movie on my channel.
00:20Low side, it is complete, you can check it.
00:23I have removed it from here.
00:26Now, I am going to reinstall it.
00:29My main purpose was to make a movie.
00:31Firstly, my brother, subscribe to the channel.
00:34Watch the whole movie.
00:36And if someone wants to take training, he can also come and take it.
00:39There was an error of F1 in this, but the problem was in its low side.
00:43Now, I am going to change this.
00:44Because of the low side, because of the fault, this IPM.
00:47My purpose of making this movie was that you get to know the way to install it.
00:53How to install it.
00:55This is also there, but once again, I made the movie.
01:00Now, I will install it here.
01:03After installing it, we will apply it, we will do the soldering.
01:06After applying this heat sink, how is it soldered?
01:11I will give you all the information right now.
01:14I have installed it like this.
01:18You see, it has come out.
01:21Now, the problem is that if I do the soldering like this,
01:25then it will go up and down from the side.
01:28Or it happened that it came up more or went down slightly at one level.
01:35So, this heat will be done and it will burn.
01:38Okay, it will be brushed at the same time.
01:40The easy solution to this is that in this, now,
01:44this heat sink, we will put it properly.
01:49You see, I have installed it now.
01:52Now, after installing it, I will install the whole screw of it.
01:56It will not happen that I have installed two, three, five.
02:00No, I will install it completely.
02:02As many as there are, it does not happen that if,
02:05anyway, you have to watch the whole movie carefully.
02:08This is of great benefit because if you install it as a common man,
02:13then often this claim comes that when you screw it,
02:16it cracks from inside or does not crack.
02:19So, this problem also comes in it that often it is said that
02:22it burned after a few days.
02:25This often comes in it, it starts burning again and again.
02:29And at one time, your microprocessor also burns.
02:33You see, I will install it.
02:35Now, I will install all the screws of it.
02:37First, I will install all the total screws of it.
02:42Especially for IPM, okay?
02:45Because if I let the IPM be loose,
02:48then this whole, it does not have to be tightened once.
02:53Okay?
02:54It has to be tightened in a level with great care by installing both the screws around it.
02:58So that in this, it has been changed twice or three times before.
03:04It has been changed two or three times.
03:05These guys have come to us from Pakistan.
03:10And now I have to do them well and give them.
03:13Inshallah, their complaint should not come again.
03:17The error of F1 was not being removed in this.
03:20F1 was coming.
03:21What else was there?
03:23L4.
03:24It was of L4.
03:25It is said that L4 was also coming.
03:27F1.
03:28Have you installed it before?
03:29Yes, I have installed it before.
03:31From where?
03:32I have installed it from the same place.
03:34Then?
03:35Then I have installed it from another place.
03:37I have installed it from there.
03:38Okay.
03:40Now, Inshallah, it will work perfectly.
03:43And you will not have any complaints.
03:45Inshallah.
03:47See this.
03:48I am installing this so that the whole level is made.
03:51It should not be that from one side, it is left from somewhere.
03:54Even a little, it will be damaged at the same time.
03:58Do not over-tighten it.
03:59Do not break it by pressing it.
04:02Just do not over-press it a little.
04:05Now see, it has come out in a level.
04:08Now you will not know how it is installed.
04:11Now I will take you out on the screen.
04:19See this.
04:20Now we have to do the soldering.
04:22How to do it?
04:23How to do it?
04:24See this.
04:25You put it like this.
04:26I put it here.
04:27Okay.
04:28See like this.
04:29One is installed.
04:30See this.
04:31It is a very useful thing.
04:32Understand.
04:33It is installed like this.
04:34After this, we will come here.
04:35Do not solder it all of a sudden.
04:37It is not that you start from the top and run from one side.
04:41Never do such soldering.
04:43Because if you do such soldering,
04:45then the system installed below,
04:47the IC,
04:48that overheats.
04:50So never do such a thing.
04:52Now this is installed.
04:53Now after this, we will install this.
04:55I will solder it in the same order.
04:58Because if I do it in one order,
05:02then it will heat from below.
05:04Okay.
05:05Never do such soldering to any IC.
05:08See this.
05:09We have to do such soldering like this.
05:12Okay.
05:13Keep this thing in mind.
05:14Because if you do it directly like this,
05:16it will happen.
05:17No problem.
05:18It will work.
05:19Do not say that we do it like this every day.
05:22It works.
05:23It will work.
05:24But its limit,
05:26the limit is reduced.
05:29Never do this to any IC.
05:32Do not do this.
05:33Do this.
05:34Do this.
05:35See this.
05:36I am doing this.
05:37The video becomes long.
05:39Watch it.
05:40Never do such a video.
05:42It is not my loss.
05:43It is yours.
05:44There are many things that we have to tell.
05:47You do the video like this.
05:49You will not understand.
05:50Okay.
05:51See this.
05:52Like this.
05:53Now I do it like this.
05:54See this.
05:55Okay.
05:56I do it like this.
05:57Slowly.
05:58Now I leave two or three.
05:59Okay.
06:00Now I come here.
06:01But I am giving two in all.
06:02Just like this.
06:03Itwill not work.
06:04But this will remove the heat.
06:05Now I move to the other end.
06:06Okay.
06:07This.
06:08I am going to sew this.
06:09Okay.
06:10See this.
06:11Like this.
06:12It is not connected.
06:13I am doing like this.
06:14Now it is your turn.
06:15This utmost positive.
06:16Alright.
06:17See this.
06:18If you do this,
06:19you mustice it with solder iron.
06:20Whole,
06:21Like this.
06:22Okay?
06:23Way to increase heat.
06:24Like this.
06:25You mustice like this.
06:26Like this.
06:27sir?
06:28There is no heat.
06:29Does not make any difference to work.
06:30You can see that it has heated up.
06:32Now this side is done.
06:36The other side is done.
06:38You have to do the same for this side.
06:40You can see that it is done.
06:42I have picked it up in the same way.
06:44Now I have come to the low side.
06:46You can see that I have come to the low side.
06:48So that it cools down a little.
06:50You should never do the soldering like this.
06:52That is why I am telling you this.
06:54These things are not told by the common man in the video.
06:58Now do it like this.
07:00You can see that it has become like this.
07:04Now I will leave it.
07:06I will come here again.
07:10I have told you the trick.
07:12If you do it like this,
07:14there are many things which
07:20You can see that it has become like this.
07:22Now we will put it like this.
07:28The paste that I have used in this is also good.
07:30Do not use light paste.
07:36And the solder iron
07:38is that
07:40the tape inside it
07:42like
07:44if you put it,
07:46it glows a little in it.
07:48It will not do in this.
07:50We put that.
07:52Because if it glows in it,
07:54then there is such a problem.
07:56You understand that
07:58the problem is gone.
08:00Now this is the last one.
08:02Now let it cool down a little more.
08:20We will clean it later.
08:22How much is left now?
08:24Now one or two are left.
08:30Now you have seen that
08:32it had to be better
08:34because
08:36how many times have you put it?
08:38I have put it three times.
08:40You have put it three times.
08:42The customer is sitting next to me.
08:44You have put it three times.
08:46Now if this duct had come,
08:48then you yourself understand
08:50that we had to do it like this.
08:52It had to be very good.
08:54But there is a compulsion
08:56that there is a lot of damage
08:58in the print etc.
09:00We will try to put it
09:02like genuine.
09:04God willing, it will be.
09:06And it will not be felt again
09:08that it has been repaired again.
09:14The solder we use
09:16is also pure number one.
09:18The amount of lead in it
09:20is very less.
09:22In fact, it is almost impossible
09:24to not have lead.
09:28Our soldering is complete.
09:30Now let me show you the duct.
09:34Now you can see from here
09:36that it is soldered
09:38exactly like the original.
09:40Our soldering is complete.
09:42Because they took it out three or four times
09:44and brought it.
09:46So if there is a little problem,
09:48otherwise we tried
09:50to do it in a good way.
09:52Now let's run it and see
09:54that there is no problem in it.
09:56Otherwise, the error of FF1
09:58has been removed or not.
10:00We started putting paste on it.
10:02After doing the paste,
10:04we will put the heat sink.
10:06We will tighten the screw of it.
10:08After applying the paste.
10:10Look, I will apply the paste
10:12on it like this.
10:14Try the video.
10:16I will tell you the whole work.
10:18If you want to learn everything,
10:20then watch the whole video
10:22and like it.
10:24And remember to subscribe to my channel.
10:26So that whenever our video comes,
10:28you get a notification
10:30and you can watch the new video.
10:32If you watch this video
10:34and do all the work,
10:36then you can do something
10:38next season.
10:42But often people say
10:44that there is no need
10:46to apply paste here.
10:48But the benefit of paste is that
10:50the air gap in it will
10:52eliminate the air gap.
10:54This is the benefit of paste.
10:56Apply paste and try
10:58to apply it.
11:02Now I have applied the paste.
11:04Now I will put the heat sink
11:06on it and put the screw
11:08on it.
11:10So that you can see it.
11:12This is my number.
11:14If you want to contact
11:16any brother,
11:18you can contact him.
11:22Now I have put this
11:24above because
11:26I had to put it upside down.
11:28I had to put it here.
11:30So I had to put it upside down
11:32because I have not cut it yet.
11:34Now we cut this too.
11:36Let's put it first.
11:38So that we can cover it
11:40and it does not move.
11:42When it moves,
11:44when it is a little on the side,
11:46then the paste will come down
11:48on our side.
11:58This screw is OK.
12:00Now see
12:02what is the important thing
12:04to see in this.
12:06That's why I keep telling you
12:08that our screw is OK.
12:10Now see
12:12this thing, we will cut it
12:14because I have put a new IPM.
12:16Now the stage of cutting it
12:18is up to you because
12:20if you cut it like a mango,
12:22then it will look
12:24like a very bad cutting.
12:26See, we do it like this.
12:28You have to take two pieces of mango
12:30and put it on it.
12:32See, I have
12:34put it on it.
12:36OK.
12:38Now see,
12:40this is our cutter.
12:42Now take the cutter
12:44and from here
12:46in one level
12:48press it from the bottom.
12:50OK.
12:52Now I am cutting it like this.
12:54OK.
12:56Whenever I cut it like this,
12:58the benefit of this is that
13:00we get cutting in one level.
13:02OK.
13:04Now I am cutting it.
13:06See,
13:08the cutting is done in one level.
13:10It is not cut from the top.
13:12Now I am cutting it
13:14in this level.
13:16See.
13:18OK.
13:20The problem is that
13:22your work should be so careful
13:24that the common man
13:26says that it is genuine.
13:28You should be careful.
13:30See.
13:32It is not a difficult work.
13:34It is a little hard work.
13:36The video is long, but it is good.
13:38You should watch it.
13:40I don't make such videos
13:42that common people make.
13:44See, it is done.
13:46See, this wire was burnt.
13:48This spiral is finished.
13:50We don't make such videos.
13:52The video is genuine and good.
13:54But it is not the same
13:56that wires are burnt
13:58and wires are not removed.
14:00You should learn this.
14:02Now we have leveled it.
14:04See, it is 100% level.
14:08Now I am going to run it.
14:10You have to see
14:12that the compressor starts.
14:14The customer is sitting with me.
14:16We have to give it.
14:18Now we run it.
14:20This is the outdoor motor.
14:22This is the indoor motor.
14:24This is the communication motor.
14:26This is the compressor.
14:28After installing the compressor,
14:30I will run it.
14:32See, it is on.
14:34See, I have turned it on.
14:36The lights are on.
14:38It is off.
14:40I have turned it on.
14:42I have set the temperature to 16.
14:44This is the outdoor motor.
14:46You can see it.
14:48This is the indoor motor.
14:50The compressor is on.
14:54We have put the IPM.
14:56Now you can understand
14:58that how to complete
15:00the IPM.
15:04Now the IPM will be completed.
15:06See the speed.
15:08I have put the load on it.
15:20Our kit is ready.
15:22If you like my video,
15:24like and share it.
15:26Subscribe to my channel.
15:28If you want to take training,
15:30you can see this number.
15:32You can take training.
15:36Khuda Hafiz
Comments